Primers for Floor Coatings

Phone 01380 831299 to place order.
Prices, excluding VAT and delivery:
(Delivery for up to £300 order value is £14.00, over £300 f.o.c. for all pre-paid orders only.)
We accept Debit Cards, Credit Cards, BACS and cheques. (Credit facilities available, subject to status.)

Low Viscosity Solvent Free Epoxy Primer
2 pack epoxy resin primer for use with FS EpoxyCoat Range
Solvent free, 100% solids formulation
Low viscosity ensures ease of application
Good penetration to ensure excellent adhesion to most substrates
Non taint, suitable for food factories

With the addition of fine quartz can be applied as a scrape coat to remove the worst undulations in the substrate and to hide fine cracks.
Note: No coverage rates can be given to achieve this as it will vary tremendously, depending on the state of the floor.
COSHH Sheets by request
Data Sheet - FS Epoxy Prime

Phone 01380 831299 to place order.
Prices, excluding VAT and delivery:
(Delivery for up to £300 order value is £14.00, over £300 f.o.c. for all pre-paid orders only.)
We accept Debit Cards, Credit Cards, BACS and cheques. (Credit facilities available, subject to status.)

Adhesive Primer for extremely smooth surfaces such as power floated or glazed concrete, ceramic tiles, etc. Offers a perfect bond between substrates and subsequent coating without blasting, etching, or other costly surface preparation techniques, thereby making real savings.

Water based
Whitish, translucent 2K Epoxy Primer
Low material usage (add water at 15 - 20% and apply a mist coat) - practical coverage of 20 to 25 sq m/litre
To be overcoated with virtually any paint or coating
Overcoat from 16 to 24 hours
Use on power floated concrete, ceramic tiles, glass, etc
(NB: If slab sealed with Proseal do a small trial area before purchasing or proceeding to coat the whole area as it this product may cause adhesion problems.)
Available in 1 and 5 litre units

Phone 01380 831299 for data and COSHH sheets

Phone 01380 831299 to place order.
Prices, excluding VAT and delivery:
(Delivery for up to £300 order value is £14.00, over £300 f.o.c. for all pre-paid orders only.)
We accept Debit Cards, Credit Cards, BACS and cheques. (Credit facilities available, subject to status.)

Fast Cure Low Viscosity Solvent Free Epoxy Primer
Fast cure formulation means that a finishing coat can be applied later the same day
2 pack epoxy resin primer for use with FS EpoxyCoat Range, particulary FS EpoxyCoat FastCure
Solvent free, 100% solids formulation
Low viscosity ensures ease of application
Good penetration to ensure excellent adhesion to most substrates
Non taint, suitable for food factories

With the addition of fine quartz can be applied as a scrape coat to remove the worst undulations in the substrate and to hide fine cracks.
Note: No coverage rates can be given to achieve this as it will vary tremendously, depending on the state of the floor.
COSHH Sheets on request
Data Sheet - FS EpoxyPrime FastCure

Phone 01380 831299 to place order.
Prices, excluding VAT and delivery:
(Delivery for up to £300 order value is £14.00, over £300 f.o.c. for all pre-paid orders only.)
We accept Debit Cards, Credit Cards, BACS and cheques. (Credit facilities available, subject to status.)

Picture shows FS EpoxySeal Clear as a seal coat for a decorative finish

Clear water dispersed primer / epoxy coating for dustproofing concrete floors
2 pack water dispersed high wear epoxy resin coating/primer
Non taint, chemically resistant, solvent free
Seals dusting concrete
When using as a primer gives very good adhesion to difficult surfaces such as power-floated concrete with minimal preparation or ceramic tiles, however it is advisable to purchase a small unit first to check adhesion before undertaking a large area. Some concrete sealers, particularly Proseal should be fully ground off the surface of a power-floated slab prior to application.
Sheen finish
Apply one coat when using as a primer
COSHH Sheets on request
Data Sheet - FS EpoxySeal Clear

Phone 01380 831299 to place order.
Prices, excluding VAT and delivery:
(Delivery for up to £300 order value is £14.00, over £300 f.o.c. for all pre-paid orders only.)
We accept Debit Cards, Credit Cards, BACS and cheques. (Credit facilities available, subject to status.)

Epoxy Resin Damp Proof Membrane and Primer
Used to form a surface damp proof membrane and moisture vapour suppressant to concrete or screeded floors.
Ideal for 'fast track' building projects
2 pack flexibilised epoxy resin
Inhibits water vapour transmission and isolates moisture
Facilitates the overlayment of 'green' concrete
Excellent adhesion to concrete
Allows early laying of floor covering
Easy to apply
To form an effective DPM two coats should be applied
Supplied in Clear, Brick Red & Grey so you can use a different colour for each coat to ensure that no area of the floor is missed
COSHH Sheets on request.
Data Sheet - FS Epoxy DPM Primer

Phone 01380 831299 to place order.
Prices, excluding VAT and delivery:
(Delivery for up to £300 order value is £14.00, over £300 f.o.c. for all pre-paid orders only.)
We accept Debit Cards, Credit Cards, BACS and cheques. (Credit facilities available, subject to status.)

For Strengthening Weak Sand/Cement Screeds
2 pack epoxy resin binder for strengthening weak sand/cement screeds
Solvent free, 100% solids formulation
Low viscosity ensures ease of application
Good penetration into screed
Non taint, suitable for food factories
COSHH Sheets on request
Data Sheet - FS EpoxyBinder

To ensure good adhesion and maximum life from your new floor or wall coating it is often benefical to apply a primer before applying finishing coats.
See our 'Advice' page for our recommendations as to when a primer should be used. The following information is available:
Floor Coating Selection Guide
Wall Coating Selection Guide
General Advice For Application & Maintenance of FS Floor Coatings
General Advice For Application & Maintenance of FS Wall Coatings
General Advice for Repairing Floors with FS Repair Products
Note: It is not generally necessary to use a primer for our FS EpoxySeal Range or for our FS EpoxyCoat Range when applying over an existing epoxy coating.